Designed for handheld interview and presentation applications, the Reporter features an omnidirectional dynamic capsule that is designed to allow the user freedom of use, without the technique related issues typical of directional end-address microphones.

Additionally its frequency response has been specially tailored for voice reproduction, to maximise intelligibility and deliver crisp, clear results in almost any condition.

The microphone features a durable die-cast aluminium alloy body coated in a discrete matte black anti-glare finish. An innovative multi-layer mesh basket protects the microphone from environmental noise without the need for a bulky and distracting foam wind shield.

The RØDE Podcaster is a dynamic, end-address USB microphone that combines broadcast-quality audio with the simplicity of USB connectivity, allowing recording direct to a computer without the need for an additional digital interface.

Including an audiophile quality 18-bit resolution, 48kHz sampling A/D converter, the Podcaster processes all of the analogue-to-digital conversion internally, bypassing the computer's lower quality on-board sound controller altogether.

A headphone output on the microphone body provides zero-latency monitoring, so the user can hear exactly what is being recorded, free of delay or echo.

The RØDE Broadcaster is a large diaphragm, end-address condenser microphone designed to provide the ultimate performance for broadcast vocal applications.

Its rich, full quality tailored response has an emphasised proximity effect that has made it a standard in radio stations the world over. It is equally suitable as a voice-over microphone for film and television.

The Broadcaster features an internal pop filter, designed to minimise plosives sounds that can overload the microphone capsule and distort the audio output. In addition to the Broadcaster's native 20Hz-20kHz response, a selectable high-pass filter at 75Hz is available which will prevent low-end noise such as air conditioners and traffic from being recorded.

The RØDE Lavalier is a discreet lapel microphone that provides broadcast-quality audio when close-miked in almost any scenario.

The Lavalier's low self-noise, user friendly omni-directional polar pattern and minimal appearance make it an ideal solution for film, television, video, theatre, house of worship and anywhere where a high quality microphone needs to be heard but not seen.

The microphone capsule is connected via a 1.2m (4') shielded, Kevlar® reinforced cable that has been rigorously strain tested up to 10kg to ensure reliable performance.

The included mini-furry for high wind protection ensures quality recordings in adverse environments, and the included cable management clips ensure that you are able to minimise the microphone and cable visibility, while providing maximum mobility for the wearer.

The RØDE PinMic™ is a discreet lavalier/lapel microphone with an innovative pin-through design that is not only easier to conceal than a traditional lapel microphone, but provides greater mounting versatility.

Comprised of a cabled backplate and a removable omni-directional capsule head, the PinMic™ is easily mounted onto any clothing or fabric by simply pushing the backplate pins through the back of the fabric and sliding the capsule into place on the front. The microphone backplate and cable are hidden behind the fabric, and the capsule head can be easily disguised, covered or decorated to further conceal the microphone.

The PinMic™ capsule is discrete at only 9mm deep and 11mm in diameter, and is supplied with both a black and an unpainted silver mesh head that can be further camouflaged by painting.

The i-XLR is a broadcast quality XLR to Lightning interface for iOS devices, that allows reporters, correspondents and audio professionals to quickly and easily capture professional interview dialogue to a smartphone or tablet.A generous three meter shielded cable allows the operator to store the phone in a pocket or bag, and a headphone output with adjustable level on the body makes it easy to monitor your audio during an interview.

The VideoMic Me is a compact and lightweight directional microphone for use with smartphones. It features an in-built 3.5mm TRRS output for plugging directly into a smartphone’s headphone socket. Its flexible mounting bracket accommodates a wide range of smartphones and allows the microphone to be fitted for primary camera or front camera ('selfie') use. A 3.5mm headphone jack on the rear allows for play-through of audio while recording (app dependent) as well as easy playback of your videos without having to remove the microphone.

The SC6-L is a simple input/output breakout box designed for Apple iOS devices. Inspired by the original SC6 with a 3.5mm TRRS jack, the SC6-L uses a Lightning Connector to connect directly to Apple iOS devices.

The Dead Cat windshield is designed for minimising any wind noise when recording in high wind conditions. Its artificial fur is specially designed so as to minimise wind noise while remaining acoustically transparent.

The DeadCat VMP is a furry wind cover for the VideoMic Pro, designed for use in windy environments. Its artificial fur is specially designed so as to minimise wind noise while remaining acoustically transparent. The DeadCat VMP is compatible with the VideoMic Pro rubber-band models only.

The DeadWombat windshield is designed for minimising wind noise when recording in high wind conditions using the RØDE Blimp. Its artificial fur is specially designed so as to minimise wind noise while remaining acoustically transparent.

The MINIFUR-LAV is a synthetic fur cover for the Lavalier microphone, designed for use in outdoor or high-wind conditions.

The MINIFUR-LAV is a synthetic fur cover for the Lavalier microphone, designed for use in outdoor or high-wind conditions.

The RØDE WS6 Deluxe Windshield is an easy to use high-performance windshield for shotgun microphones. Designed to reduce wind noise when recording in adverse environmental conditions, the WS6 combines an open-cell foam surround with an outer layer of acoustically transparent artificial fur. A rubber base prevents any wind noise from entering the rear of the microphone pickup area. Suitable for the RØDE NTG1, NTG2, NTG4 and NTG4+ as well as any shotgun microphone with a maximum slot length of 160.5mm (6 1/4") and a diameter of 21-22.5mm.

The RØDE WS7 Deluxe Windshield is an easy to use high-performance windshield for shotgun microphones. Designed to reduce wind noise when recording in adverse environmental conditions, the WS7 combines an open-cell foam surround with an outer layer of acoustically transparent artificial fur. A rubber base prevents any wind noise from entering the rear of the microphone pickup area. Suitable for the RØDE NTG3 and any shotgun microphone with a maximum slot length of 186.5mm (7 1/4") and a diameter of 19-20mm.

The WS-LAV is a high quality pop filter, designed to fit the Lavalier microphone. A pop filter should be fitted in the majority of applications to prevent any hard plosive sounds overloading the microphone capsule. The WS-LAV is supplied as a pack of three.

The RØDE Micro Boompole provides ultimate boom pole performance in a convenient and portable size. Intuitive twist locks allow the Micro Boompole’s three sections to smoothly extend to 2063mm (6¾’), while the ergonomic grip provides comfort during use.

The Micro Boompole Pro is a unique, modular booming device that allows location sound engineers to capture audio in confined or difficult spaces.Optimised for use with the VideoMicro microphone, the Micro Boompole Pro’s three sections combine to a maximum length of 2.2m (7’2”). Using an industry standard 3/8” thread, these sections can also be used to extend the Boompole Pro to reach to over 3.7m (12').

The BoomPole Bag is a high-quality neoprene carry bag designed to accommodate a boompole with shock mount and microphone attached.

The RØDE Boompole Clips are designed to quickly and easily mount onto any RØDE boompole to secure the microphone lead and minimise any movement.

The RØDE Blimp is a complete windshield and shock mounting accessory for the NTG1, NTG2, NTG3, NTG4 and NTG4+ microphones, as well as any third party shotgun microphone up to 325mm (12 ¾”) in length. Now featuring the Rycote® Lyre suspension system, the Blimp provides the ultimate in microphone suspension and isolation. Constructed from a single piece of hard-wearing thermoplastic, the Lyre provides superior acoustic suspension to traditional elastic solutions, and will never wear out, sag or snap. The Blimp’s handle has also been completely redesigned, reducing the product weight significantly, while increasing the ergonomics for handheld use. Housed inside the grip is a heavy-duty Mogami cable which splits via a junction box to a highly-flexible thin cable inside the Blimp, to minimise the transference of vibration to the microphone. With the lightweight design of the handle and suspension system the new Blimp design is over 25% lighter (550gm without microphone or DeadWombat fitted). The Blimp attaches to any standard boompole via 3/8" thread attachment at the base. The Universal Blimp Mount is available as an option to remove the handle when the Blimp is being used primarily on a boompole to reduce weight.

The PG1 Cold Shoe Pistol Grip is a convenient and ergonomic way to operate your RØDE VideoMic, Stereo VideoMic, or any other cold-shoe device independently of your video camera. A convenient 3/8” thread on the base allows connection to a boompole or microphone stand, while the spine features handy cable management.

The perfect suspension shock mount for the Procaster or Podcaster, the PSM1 provides isolation from external vibrations which can translate as low frequency noise or manipulate the microphone position. The PSM1 gives you confidence when using your microphone in environments where there is any movement that may interfere with the microphones performance.

The RØDE Pivot Adaptor is a durable machined-aluminium, brass and high-grade polymer adaptor for mounting on boom stands and boompoles, allowing for up to 210 degrees of pivot.

The RØDE Vampire Clip is a double-toothed clothing pin that conveniently fastens the RØDE Lavalier microphone onto a wide range of fabric and clothing for complete mounting versatility.

The Violin-Clip suspension mount is designed to easily clamp onto the strings of a violin in the bridge area behind the top plate, allowing for the precise mounting of a lavalier microphone.

The RØDE Stereo Bar is a robust solution for mounting two microphones in a stereo array. With clearly marked spacing of up to 20cm, as well as angle and measurement indicators for ORTF and XY positioning, the RØDE Stereo Bar makes it quick and easy to achieve complex recording arrays. The 5/8” mounting threads are supplied with accompanying spacing clips to allow for easy positioning for stacked arrays, and the robust ABS construction makes the Stereo Bar stable and durable, allowing it to easily support the weight of two large diaphragm microphones.

The SM2 is a suspension shock mount that holds a range of large diaphragm condenser microphones. It provides isolation from external physical factors that may cause unwanted rumble and vibrations in the microphone. Additionally the SM2 allows for flexible mounting to position your microphone perfectly in any situation.

The SM3-R is a suspension shock mount with camera shoe adaptor for mounting various RØDE microphones onto a camera via the standard hot/cold shoe mount.

The SM3-R is equipped with dual Rycote Lyre mounts to ensure maximum isolation from any handling vibrations, four possible mounting points to suit the complete range of compatible RØDE on-camera microphones, and integrated cable management clip.

The SM4-R is a suspension shock mount for mounting various RØDE microphones onto a mic stand or boompole with 3/8" or 5/8" thread.

The SM4-R is equipped with dual Rycote Lyre mounts to ensure maximum isolation from any handling vibrations, four possible mounting points to suit the complete range of compatible RØDE shotgun microphones, and integrated cable management clip.

The stand mount is angle adjustable and can be locked into position to ensure sturdy and reliable mic positioning.