ITC - T-112F, Volume Control Designed with 120W Separate Toroidal Transformer
Accessories for installation
Accessories for installation
Volume control is designed with separate toroidal transformer. It is the volume control in 5 steps. It is made with the plastic wall plate.
The T-212FS attenuator is designed to adjust loudspeaker volume and change sound programs in warning systems .
The T-2200FS attenuator is designed to adjust the volume of the speakers and switch sound programs in warning systems.
- Heavy-duty steel bracket
- Secure wall installation
- Compatible with ITC horns
- Quick and easy mounting
- Corrosion-resistant finish
Ambient noise sensor for the ambient noise controller
Volume control is designed with the transformer. It is 5-step volume control. It is manufactured with ABS materials.
Volume control is designed with transformer. It is volume control 5 steps. It is made of ABS materials.
Volume control is designed with transformer. It is volume control 5 steps. It is made of ABS materials.
TH-0511 is one with a low power circuit and the frequency range is 6 MHz to 8 MHz. Spherical reception of 150 degrees, covering signals in a wide range.
Wide voltage input. No-load power: <0.5W. Single output, short circuit protection. Efficient and reliable. According to the different regions, self-optional AC power cables. Suitable models: TS-0221, TS-0670HY
Recessed transformer regulator with relay (24V). High quality ABS housing. Recommended for use with V-8P plastic housing.
- Wi-Fi hotspot
- ITC system compatibility
- Extended wireless range
- Simplified installation
- Discreet compact design
This exclusive microphone arm with a 3/8" or 5/8" thread connector in a modern design features a new, innovative table clamp for quick and easy positioning of a microphone in the studio or at a multimedia work station. The 236.22" long internally guided microphone cable has a 3 pin XLR plug connector. Microphones up to a maximum of 3.307 lbs are easily held in any position. The clamping width of 0 to 1.889" allows the clamp to be attached to a wide variety of surfaces.
The PSA1 is a professional studio boom arm that allows easy and precise placement of a microphone. It features an innovative parallelogram design that keeps the mic direction constant as the height is adjusted, as well as internal springs for quiet operation.
- DC-free loudspeaker tap-off connection
- Compatible with 70/100 V
- Up to 20 W tap-off
- 500 W loop capacity
- Detachable screw terminal connectors
- Wi-Fi AC up to 1167 Mbps
- Dual-band 2.4/5 GHz wireless
- PoE or 12V power
- QoS traffic priority management
- Seamless wireless network roaming
- Simple reliable rotary operation
- Steel bracket for LC1 speakers
- Two integrated ceiling clamps
- 190-millimeter circular mounting cutout
- Supports ceilings up to 50mm
- Optional safety cable attachment
- Wall or hard-ceiling mounting
- Durable white ABS enclosure
- Fits LC1 ceiling loudspeakers
- Side and rear cable access
- Optional single-point suspension kit
- Single-point suspension for LC1 speakers
- Rugged triangular steel mounting plate
- Three chains with central eye-hook
- Compatible with Bosch LC1-CSMB box
- Fast secure suspended installation system
- Eight power relays
- Ethernet network control
- Integrated RS-232 control
- 20 A per channel
- Manual emergency switching
- Simultaneous charging of 10 devices
- Fast charging up to 18W
- Automatic charging current adjustment
- Built-in electrical overcurrent protection
- Short-circuit protection and automatic recovery
- Built-in 2 × 30 W
- IP network audio
- 4.3-inch TFT display
- USB and IR remote
- Local and network playback
- IP audio encoding
- Dual RCA audio inputs
- 100 Mbps networking
- Compact aluminum housing
- Real-time audio streaming
- 10 m extension cable
- 6-pin aviation connectors
- Stable signal transmission
- Plug-and-play installation
- ITC conference compatible
- Heavy-duty wall mounting
- Reinforced steel construction
- Fast secure installation
- Compatible with multiple speakers
- Durable black finish